Run CCC ONE Estimate Completeness QC Checklist — Free

Inspection Details and Estimate Scope

Estimate identifier, vehicle, and repair scope are confirmed

Verify the estimate is tied to the correct RO/claim number, vehicle identification, and documented repair scope before review.

Repair plan matches visible damage and documented teardown findings critical (required)

Confirm the estimate reflects the current repair plan, including any teardown discoveries that affect labor, parts, or procedures.

Yes No N/A

Supplement or prior revision history reviewed

Check whether prior supplements, revisions, or prior estimate versions were reviewed for missing operations or duplicated line items.

Yes No N/A

OEM repair information source documented

Confirm the estimate references the correct OEM repair information source or procedure set used during the review.

Estimate is ready for upload after QC review critical (required)

Final readiness check for completeness, accuracy, and internal approval before estimate upload.

Yes No N/A

Not-Included Operations Review

Disassembly and reassembly operations captured where required critical (required)

Verify any not-included disassembly, reassembly, or setup labor is added when required by the repair process.

Yes No N/A

Clip, fastener, seam sealer, and consumable operations included as applicable

Confirm commonly not-included operations and materials are added when needed for the repair.

Yes No N/A

Scan, calibration, and diagnostic operations reviewed for inclusion critical (required)

Check whether pre-repair, post-repair, or in-process scan and calibration requirements were captured where applicable to the repair plan.

Yes No N/A

Weld, sectioning, structural setup, and measuring operations captured critical (required)

Verify structural repair labor, measuring, setup, and related operations are included when required by the damage path.

Yes No N/A

Hazardous material handling or disposal charges included when applicable

Confirm any applicable disposal, handling, or environmental charges are included in the estimate when required by the repair process.

Yes No N/A

Refinish Time and Paint Operations

Refinish labor time is present for all repaired refinishable panels critical (required)

Verify each panel requiring refinish labor has a corresponding time entry and that no refinishable surface is omitted.

Yes No N/A

Blend operations included where required by color match or OEM procedure critical (required)

Confirm blend time is added when necessary for color match, adjacent panel repair, or OEM-directed refinishing procedures.

Yes No N/A

Paint materials and related refinish materials are captured

Check that paint materials, primers, clearcoat, and related refinish materials are included according to shop process and estimate rules.

Yes No N/A

Masking, tinting, and related prep operations reviewed

Verify prep and ancillary refinish operations are included where needed and not left out as non-billable assumptions.

Yes No N/A

Refinish labor appears reasonable for the documented damage path

Confirm the total refinish time aligns with the damage extent, panel count, and repair method documented in the estimate.

OEM Procedures and Safety Requirements

OEM-required procedures are identified and included critical (required)

Verify all applicable OEM repair procedures, replacement steps, and special operations are captured in the estimate.

Yes No N/A

OEM-required safety inspections are included where applicable critical (required)

Confirm any OEM-required safety inspection or verification step is added when the repair path calls for it.

Yes No N/A

ADAS, restraint, or electronic reset procedures reviewed critical (required)

Check for required electronic resets, module initialization, calibration, or restraint-system procedures tied to the repair.

Yes No N/A

Supplemental labor for OEM procedures captured

Verify labor associated with OEM procedures is included and not assumed to be covered by standard body or refinish operations.

Yes No N/A

Procedure source and revision date documented

Record the OEM source and revision date used to support the estimate content review.

Estimate Quality, Completeness, and Sign-Off

No obvious omitted operations remain after QC review critical (required)

Final completeness check for missing labor, parts, procedures, or related operations before upload.

Yes No N/A

All deficiencies documented for correction or supplement

List any non-conformances, missing operations, or estimate corrections identified during the review.

Inspector signature critical (required)

QC reviewer attestation that the estimate was reviewed for completeness prior to upload.

Get your results

Enter your email — we'll send you a PDF of your filled-out template, plus the occasional MangoScoop newsletter (templates, workflow tips, product updates). Unsubscribe anytime — link is in every email.

Email (required)

Your name (optional)

Run: CCC ONE Estimate Completeness QC Checklist

Inspection Details and Estimate Scope

Not-Included Operations Review

Refinish Time and Paint Operations

OEM Procedures and Safety Requirements

Estimate Quality, Completeness, and Sign-Off

Get your results