Run Inverter-Based Resource Ride-Through Commissioning Record — Free

Inspection Details

Asset identification and commissioning scope recorded

Record the plant, inverter, feeder, or unit name; equipment ID; location; and commissioning scope.

Inspection date and time captured

Document when the commissioning inspection was performed.

Inspector and responsible engineer identified

Enter the inspector name, title, and the responsible commissioning engineer or authorized representative.

Applicable interconnection or utility requirements referenced

List the governing interconnection agreement, utility standard, OEM procedure, or project specification used for this commissioning record.

Commissioning status

Select the current commissioning state of the inverter-based resource.

Safety and Test Preconditions

Energized work controls and LOTO boundaries established critical (required)

Verify lockout-tagout boundaries, energized work permits if applicable, and safe work boundaries are in place per OSHA 1910.147 and site procedure.

Yes No N/A

Arc-flash and shock PPE available and appropriate critical (required)

Confirm PPE selection is consistent with the task and equipment condition, including arc-rated clothing, gloves, face protection, and other required PPE per site electrical safety program and NFPA 70E practices.

Yes No N/A

Test instruments calibrated and within certification date critical (required)

Verify relay test sets, power quality meters, oscillography tools, and any reference instruments are calibrated and traceable.

Yes No N/A

Site conditions safe for commissioning activity

Confirm access paths are clear, no active hazards are present, and the work area is suitable for testing and observation.

Yes No N/A

Emergency shutdown and communication method confirmed critical (required)

Verify the emergency stop, shutdown sequence, and communications path with the control room or operator are understood before testing.

Yes No N/A

Ride-Through Performance Settings Verification

Voltage ride-through settings match approved design critical (required)

Verify undervoltage and overvoltage ride-through thresholds, time delays, and trip curves match the approved commissioning package or OEM-approved settings.

Yes No N/A

Frequency ride-through settings match approved design critical (required)

Verify underfrequency and overfrequency ride-through thresholds, time delays, and trip curves match the approved commissioning package or OEM-approved settings.

Yes No N/A

Ride-through mode enabled on all applicable inverter units critical (required)

Confirm ride-through functions are enabled and not bypassed, blocked, or left in a temporary test state on any in-service unit.

Yes No N/A

Protection coordination does not create unintended tripping critical (required)

Verify protective relay settings, inverter controls, and breaker logic are coordinated so that expected ride-through behavior is not defeated by nuisance trips.

Yes No N/A

Settings file or parameter export archived

Confirm the final parameter set, relay file, or controller export is saved in the project record and traceable to the tested configuration.

Yes No N/A

Disturbance Monitoring and Event Recording Setup

Disturbance recording function enabled critical (required)

Verify oscillography, event recording, or disturbance capture is enabled on the inverter controller, relay, or plant controller as applicable.

Yes No N/A

Time synchronization configured critical (required)

Confirm the device time source is configured and synchronized so event records can be correlated across equipment.

Yes No N/A

Event trigger thresholds verified

Verify trigger thresholds for voltage, frequency, current, or status changes are set to capture relevant disturbances without excessive false triggers.

Yes No N/A

Recorded channels are sufficient for ride-through analysis critical (required)

Confirm the monitored channels include the signals needed to evaluate voltage, frequency, inverter output, breaker status, and control actions.

Yes No N/A

Data retention and retrieval process confirmed

Verify event files can be retrieved, retained, and exported in a usable format for compliance review or disturbance analysis.

Yes No N/A

Functional Ride-Through Test Results

Voltage disturbance test completed successfully critical (required)

Document whether the resource remained connected and performed as expected during the applied voltage disturbance test.

Yes No N/A

Photo evidence (optional)

Frequency disturbance test completed successfully critical (required)

Document whether the resource remained connected and performed as expected during the applied frequency disturbance test.

Yes No N/A

Photo evidence (optional)

Observed response matches expected ride-through behavior

Rate how closely the observed response matched the approved ride-through criteria and commissioning expectations.

Deficiencies, Corrective Actions, and Sign-Off

Deficiencies or non-conformances documented

Record any deficiency, non-conformance, or deviation from the approved ride-through commissioning criteria.

Corrective actions assigned with owner and due date

Document the corrective action, responsible party, and target completion date for each open item.

Inspector signature

Inspector attests that the record is complete and accurate.

Responsible engineer or owner representative signature

Authorized reviewer acknowledges the commissioning results and any open items.

Get your results

Enter your email — we'll send you a PDF of your filled-out template, plus the occasional MangoScoop newsletter (templates, workflow tips, product updates). Unsubscribe anytime — link is in every email.

Email (required)

Your name (optional)

Run: Inverter-Based Resource Ride-Through Commissioning Record

Inspection Details

Safety and Test Preconditions

Ride-Through Performance Settings Verification

Disturbance Monitoring and Event Recording Setup

Functional Ride-Through Test Results

Deficiencies, Corrective Actions, and Sign-Off

Get your results