Run Electrical Trim-Out Inspection Checklist — Free

Inspection Details

Project, area, and inspection date recorded

Record the project name, inspected area, floor/room number, and date of inspection.

Inspector and responsible electrical lead identified

Enter the inspector name and the electrical foreman, supervisor, or responsible lead for follow-up.

Inspection stage confirmed as trim-out

Confirm this inspection is being performed at the trim-out phase after rough-in and before final turnover.

Devices and Receptacles

Devices installed plumb, level, and securely fastened critical (required)

Verify switches, receptacles, and other devices are aligned, firmly mounted, and not loose in the box.

Yes No N/A

Photo evidence (optional)

Device faceplates and cover plates installed with no gaps or damage critical (required)

Check that all plates are present, properly sized, unbroken, and fully cover the opening without exposed conductors or box edges.

Yes No N/A

Photo evidence (optional)

Receptacle and switch devices match approved device schedule

Confirm device type, color, rating, and configuration match the approved plans, submittals, and room schedule.

Yes No N/A

Tamper-resistant or weather-resistant devices installed where required critical (required)

Verify required TR or WR devices are installed in the correct locations per design and code requirements.

Yes No N/A

Photo evidence (optional)

Receptacles and switches free of cracks, scorch marks, or loose conductors critical (required)

Inspect for physical damage, heat discoloration, arcing evidence, or visible conductor issues.

Yes No N/A

Photo evidence (optional)

Luminaires and Lighting Controls

Luminaires mounted securely and aligned as specified critical (required)

Verify fixtures are firmly mounted, properly supported, and located per the approved lighting layout.

Yes No N/A

Photo evidence (optional)

Lamps, trims, lenses, and diffusers installed and undamaged

Confirm all fixture components are present, seated correctly, and free from cracks, chips, or missing parts.

Yes No N/A

Photo evidence (optional)

Lighting controls operate correctly

Test switches, dimmers, occupancy sensors, and other controls for proper on/off operation and intended response.

Yes No N/A

Emergency or egress lighting energized and functional where installed critical (required)

Verify emergency lighting and exit-related fixtures operate as intended during test conditions.

Yes No N/A

Photo evidence (optional)

Fixture labeling and circuit identification visible where required

Confirm fixture tags, control labels, or circuit identifiers are present and legible where specified.

Yes No N/A

Panel Directory and Circuit Identification

Panel directory is complete, legible, and accurate critical (required)

Verify each breaker or circuit is identified clearly and matches the actual loads served.

Yes No N/A

Photo evidence (optional)

Circuit labeling matches as-built conditions

Check that field-installed labels correspond to the current room and equipment assignments.

Yes No N/A

Panel cover installed with all fasteners present critical (required)

Verify the deadfront or panel cover is installed correctly, secured, and free of missing screws or open knockouts.

Yes No N/A

Photo evidence (optional)

Panel interior free of debris, unused hardware, and foreign objects critical (required)

Inspect the enclosure interior for wire clippings, packaging, tools, or other contamination.

Yes No N/A

Photo evidence (optional)

Working clearances and access to panel maintained critical (required)

Confirm the panel is accessible and not blocked by stored materials or installed finishes.

Yes No N/A

Photo evidence (optional)

GFCI and AFCI Functional Testing

GFCI devices trip and reset properly critical (required)

Test each required GFCI device or breaker using the test function and verify reset restores power.

Yes No N/A

AFCI devices trip and reset properly critical (required)

Test each required AFCI device or breaker using the test function and verify reset restores power.

Yes No N/A

Downstream outlets protected by GFCI/AFCI devices verified where applicable

Confirm downstream protection is present and functioning for circuits intended to be protected by a device or breaker.

Yes No N/A

Test records or device indicators documented

Record the device location, test result, and any indicator status or fault condition observed during testing.

Yes No N/A

Photo evidence (optional)

Deficiencies and Closeout

Deficiencies documented with location and corrective action critical (required)

List all deficiencies, non-conformances, and punch-list items with exact location and required correction.

Photo evidence attached for all critical deficiencies

Attach photos showing the issue and, when available, the corrected condition.

Yes No N/A

Photo evidence (optional)

Inspector sign-off completed critical (required)

Inspector signature confirming the inspection was completed and findings were recorded.

Get your results

Enter your email — we'll send you a PDF of your filled-out template, plus the occasional MangoScoop newsletter (templates, workflow tips, product updates). Unsubscribe anytime — link is in every email.

Email (required)

Your name (optional)

Run: Electrical Trim-Out Inspection Checklist

Inspection Details

Devices and Receptacles

Luminaires and Lighting Controls

Panel Directory and Circuit Identification

GFCI and AFCI Functional Testing

Deficiencies and Closeout

Get your results