Run Cable Termination and Glanding Record — Free

Inspection Details

Circuit, panel, or equipment identifier recorded

Record the exact cable/circuit reference, panel name, equipment tag, or feeder identifier.

Inspection date and time recorded critical (required)

Document when the termination and glanding verification was completed.

Inspector name and qualification recorded critical (required)

Enter the inspector name and confirm the person is authorized or competent for electrical verification.

Work status identified

Select whether the cable is new installation, re-termination, maintenance repair, or post-test verification.

Reference drawing, SOP, or torque specification available critical (required)

Confirm the applicable drawing, wiring schedule, manufacturer instruction, or torque specification is available at the point of inspection.

Yes No N/A

Cable Gland and Entry Verification

Correct gland type installed for cable construction critical (required)

Verify the gland type matches the cable construction, including armored, unarmored, screened, or hazardous-area requirements as applicable.

Yes No N/A

Gland rating matches enclosure and environment critical (required)

Confirm the gland rating is suitable for the enclosure ingress protection, environmental exposure, and any hazardous-area classification where applicable.

Yes No N/A

Gland installed correctly with no visible damage critical (required)

Check that the gland is fully engaged, mechanically secure, and free from cracks, deformation, or thread damage.

Yes No N/A

Photo evidence (optional)

Cable outer sheath is properly retained and sealed critical (required)

Verify the outer sheath is retained by the gland and the entry is sealed without gaps, loose components, or exposed conductors.

Yes No N/A

Earth tag, shroud, or sealing washer installed where required

Confirm all required gland accessories are fitted according to the cable type and installation method.

Yes No N/A

Termination and Lug Torque Verification

Conductor termination matches drawing and terminal designation critical (required)

Verify each conductor is landed on the correct terminal, phase, or device point per the approved wiring diagram.

Yes No N/A

Lug size and conductor size are compatible critical (required)

Confirm the lug is correctly sized for the conductor cross-section and terminal stud or clamp arrangement.

Yes No N/A

Lug torque value recorded critical (required)

Record the applied torque for each termination or the representative torque value used for the set.

Note (optional)

Applied torque meets specified torque requirement critical (required)

Confirm the measured torque is within the specified tolerance for the lug, terminal, and hardware combination.

Yes No N/A

Termination hardware secure and correctly assembled critical (required)

Check that washers, spring washers, nuts, and lock devices are installed in the correct order and fully secured.

Yes No N/A

Polarity, Phase Identification, and Screen Bonding

Polarity or phase identification verified at termination critical (required)

Confirm polarity, phase sequence, or conductor identification is correct against the wiring schedule and test results.

Yes No N/A

Cable screen or shield bonded at the designated end(s) critical (required)

Verify the screen or shield is bonded exactly as specified, including single-end or both-end bonding requirements.

Yes No N/A

Screen bonding continuity verified critical (required)

Confirm the screen bonding connection is continuous, mechanically secure, and free from loose strands or poor contact.

Yes No N/A

Earthing or grounding conductor termination verified critical (required)

Check that the protective earth or grounding conductor is terminated to the correct point and is secure.

Yes No N/A

End-to-end identification labels present and legible

Verify cable markers, ferrules, or labels are installed and legible at both ends where required.

Yes No N/A

Deficiencies, Corrective Action, and Sign-Off

Deficiencies or non-conformances documented

Record any defects, deviations, or non-conformances found during the inspection, including location and impact.

Corrective action assigned and tracked

Document the corrective action, responsible person, and target completion date for any failed item.

Inspector signature critical (required)

Inspector confirms the record is accurate and complete.

Supervisor or commissioning sign-off

Optional supervisory or commissioning approval for release to service, where required by site procedure.

Get your results

Enter your email — we'll send you a PDF of your filled-out template, plus the occasional MangoScoop newsletter (templates, workflow tips, product updates). Unsubscribe anytime — link is in every email.

Email (required)

Your name (optional)

Run: Cable Termination and Glanding Record

Inspection Details

Cable Gland and Entry Verification

Termination and Lug Torque Verification

Polarity, Phase Identification, and Screen Bonding

Deficiencies, Corrective Action, and Sign-Off

Get your results