Run ASTM F1417 Sanitary Sewer Low-Pressure Air and Mandrel Deflection Test — Free

Inspection Details and Project Identification

Project name and location recorded critical (required)

Record the project name, site address, and sewer reach or station limits being tested.

Test date and start time recorded critical (required)

Document when the air test or mandrel test was performed.

Pipe segment identification recorded critical (required)

Identify the manhole-to-manhole reach, lateral, stationing, or segment number.

Pipe material, diameter, and length documented critical (required)

Record pipe material, nominal diameter, and tested length for the segment.

Applicable specification noted

Select the governing acceptance specification for this test record.

Pre-Test Installation and Safety Conditions

Pipeline isolated and test section sealed critical (required)

Confirm the test section is isolated, plugged, and sealed at all openings before pressurization.

Yes No N/A

Test area secured and personnel clear of hazard zone critical (required)

Verify the work zone is controlled and personnel are clear before introducing air pressure.

Yes No N/A

Air compressor, gauges, and fittings inspected for serviceability critical (required)

Confirm hoses, regulators, gauges, and fittings are in good condition and suitable for the test.

Yes No N/A

Pressure relief and control devices installed critical (required)

Verify pressure control and relief devices are in place to prevent over-pressurization.

Yes No N/A

Test section cleaned and free of debris

Confirm the line is free of debris, standing water, and obstructions that could affect the test.

Yes No N/A

Low-Pressure Air Test Setup and Conditions

Test pressure target recorded critical (required)

Record the specified test pressure used for the air test.

Note (optional)

Initial pressure stabilization completed critical (required)

Confirm the line was allowed to stabilize before the timed test period began.

Yes No N/A

Gauge calibration or verification current critical (required)

Verify the pressure gauge used for the test is within its calibration or verification interval.

Yes No N/A

Ambient conditions documented

Record weather, temperature, groundwater influence, or other conditions that may affect test results.

Test duration recorded critical (required)

Enter the timed duration used for the acceptance test.

Note (optional)

Air Test Results and Acceptance

Initial test pressure achieved critical (required)

Record the pressure at the start of the timed test period.

Note (optional)

Pressure at end of test period recorded critical (required)

Record the pressure at the end of the test period.

Note (optional)

Observed pressure loss within project acceptance criteria critical (required)

Indicate whether the pressure loss met the acceptance criteria for the tested segment.

Yes No N/A

Leaks, audible escapes, or visible defects observed critical (required)

Record whether any leaks, joint failures, or other defects were observed during the test.

Yes No N/A

Air test result critical (required)

Select the final result for the low-pressure air test.

Note (optional)

Mandrel Deflection Test

Mandrel test performed at required post-installation interval critical (required)

Confirm the mandrel deflection test was performed after the required curing or waiting period per project specification.

Yes No N/A

Mandrel size and configuration documented critical (required)

Record the mandrel diameter, number of arms, and any project-specific configuration details.

Mandrel passes through pipe without obstruction critical (required)

Verify the mandrel passes freely through the tested section, indicating acceptable deflection.

Yes No N/A

Deficiencies, Corrective Actions, and Sign-Off

Deficiencies or non-conformances documented

List any deficiencies, non-conformances, or failed test conditions.

Corrective actions assigned

Describe required repairs, retesting, or follow-up actions.

Inspector signature critical (required)

Inspector sign-off confirming the record is complete and accurate.

Contractor or owner representative signature

Optional acceptance acknowledgment by the contractor or owner representative.

Get your results

Enter your email — we'll send you a PDF of your filled-out template, plus the occasional MangoScoop newsletter (templates, workflow tips, product updates). Unsubscribe anytime — link is in every email.

Email (required)

Your name (optional)

Run: ASTM F1417 Sanitary Sewer Low-Pressure Air and Mandrel Deflection Test

Inspection Details and Project Identification

Pre-Test Installation and Safety Conditions

Low-Pressure Air Test Setup and Conditions

Air Test Results and Acceptance

Mandrel Deflection Test

Deficiencies, Corrective Actions, and Sign-Off

Get your results