Run ADA Lift and Ramp Daily Cycle Inspection — Free

Inspection Details

Inspection date and time recorded critical (required)

Vehicle or asset identifier recorded critical (required)

Enter bus number, vehicle ID, unit number, or other unique asset identifier.

Inspector name and employee ID recorded critical (required)

Inspection performed before revenue service critical (required)

Confirm the lift or ramp was inspected before the vehicle was placed in service.

Yes No N/A

Applicable SOP or manufacturer procedure referenced

Record the procedure, manual, or internal checklist used for this inspection.

Inspection location recorded

Optional location where the inspection was completed, such as depot, yard, or garage bay.

Inspection record completed legibly and retained

Confirm the daily inspection record is complete and suitable for retention per agency procedure.

Yes No N/A

Pre-Service Readiness

Area around lift or ramp clear of obstructions critical (required)

Check that the deployment area is free of debris, ice, trash, or other obstructions that could interfere with operation.

Yes No N/A

Power source and vehicle electrical system available critical (required)

Confirm the lift or ramp has the required electrical or hydraulic power available for testing.

Yes No N/A

Emergency stop and control labels legible

Verify controls, warnings, and emergency stop markings are visible and readable.

Yes No N/A

No visible fluid leaks, loose hardware, or damaged components critical (required)

Inspect the lift or ramp assembly for hydraulic leaks, loose fasteners, bent parts, frayed wiring, or other visible defects.

Yes No N/A

Photo evidence (optional)

Safety interlocks and barriers appear intact critical (required)

Confirm gates, barriers, handrails, and interlock components are present and not visibly damaged.

Yes No N/A

Cycle Test and Functional Operation

Lift or ramp deployed and stowed through full cycle without abnormal noise or binding critical (required)

Perform a full deployment and stow cycle. Observe for hesitation, binding, unusual noise, or incomplete travel.

Yes No N/A

Platform or ramp reaches full travel position critical (required)

Verify the platform or ramp extends to the required operating position and returns to the fully stowed position.

Yes No N/A

Controls respond correctly from all required operating stations critical (required)

Test the primary and any secondary controls required by the vehicle design or SOP.

Yes No N/A

Emergency stop or override functions operate as intended critical (required)

Verify emergency stop, manual override, or emergency lowering functions operate per procedure.

Yes No N/A

Door or transmission interlock prevents unsafe operation critical (required)

Confirm the lift or ramp cannot operate when the interlock condition is not satisfied, if equipped.

Yes No N/A

Load Test and Safety Verification

Load test required by procedure or manufacturer

Indicate whether a load test is required for this inspection based on the agency procedure, manufacturer guidance, or equipment condition.

Yes No N/A

Note (optional)

Load test completed successfully when required critical (required)

If a load test is required, confirm the lift or ramp operated safely with the required test load.

Yes No N/A

Test load weight recorded

Record the approximate or measured test load used during the load test.

Platform or ramp remained stable under load critical (required)

Verify there was no excessive deflection, slipping, drift, or instability during the load test.

Yes No N/A

Deficiencies and Final Disposition

Any deficiency or non-conformance identified

Mark yes if any defect, malfunction, or non-conformance was observed during the inspection.

Yes No N/A

Deficiency description and corrective action documented critical (required)

Describe the deficiency, affected component, and corrective action taken or required. Include whether the unit was removed from service if applicable.

Lift or ramp approved for service critical (required)

Confirm the equipment is safe to return to service after inspection and any required corrective action.

Yes No N/A

Get your results

Enter your email — we'll send you a PDF of your filled-out template, plus the occasional MangoScoop newsletter (templates, workflow tips, product updates). Unsubscribe anytime — link is in every email.

Email (required)

Your name (optional)

Run: ADA Lift and Ramp Daily Cycle Inspection

Inspection Details

Pre-Service Readiness

Cycle Test and Functional Operation

Load Test and Safety Verification

Deficiencies and Final Disposition

Get your results