Run Traffic Signal Loop Splice and Megger Test Inspection — Free

Inspection Details

Project / site identifier

Enter the project number, intersection name, or site identifier.

Inspection date and time critical (required)

Document when the inspection and testing were performed.

Inspector name and company critical (required)

Record the qualified inspector or competent person performing the test.

Loop location / approach / lane designation critical (required)

Identify the specific lane, approach, or detector loop location being tested.

Work order / permit / plan reference

Reference the applicable work order, permit, plan sheet, or as-built drawing.

Inspection type

Select the inspection context for this record.

Safety and Test Preconditions

Traffic control and work zone protection in place critical (required)

Confirm the work zone is protected per the approved traffic control plan.

Yes No N/A

LOTO / circuit isolation confirmed before testing critical (required)

Verify the detector circuit is isolated and safe to test before using the megohmmeter.

Yes No N/A

Test equipment calibrated and suitable for loop megger testing critical (required)

Confirm the megohmmeter or insulation resistance tester is in calibration and appropriate for the circuit.

Yes No N/A

Photo evidence (optional)

Circuit de-energized and disconnected from controller input critical (required)

Verify the loop circuit is disconnected from the controller or detector input before insulation testing.

Yes No N/A

PPE appropriate for electrical and roadway work critical (required)

Confirm required PPE is being used, including eye protection and any arc-flash or roadway PPE required by the site conditions.

Yes No N/A

Ambient conditions suitable for testing

Confirm weather and site conditions allow safe and reliable testing.

Yes No N/A

Loop Wiring and Splice Verification

Loop wire continuity from saw cut to home-run verified critical (required)

Verify the loop conductor path is continuous from the loop to the home-run termination.

Yes No N/A

Splice locations recorded and accessible for review critical (required)

Confirm all splice locations are documented and can be identified on the record or as-built sketch.

Yes No N/A

Photo evidence (optional)

Number of splices in loop circuit

Enter the total number of splices associated with this loop circuit.

Note (optional)

Home-run termination identified and labeled critical (required)

Verify the home-run termination point is identified, labeled, and traceable to the detector lead-in.

Yes No N/A

Photo evidence (optional)

Splice method and enclosure condition acceptable

Select the splice method used and confirm the enclosure or seal condition.

As-built sketch or photo set attached critical (required)

Attach photos or a marked-up sketch showing loop routing, splice points, and home-run path.

Note (optional)

Electrical Test Results

Loop resistance measured critical (required)

Record the measured loop resistance.

Note (optional)

Insulation resistance to ground measured critical (required)

Record the megohmmeter reading from the loop conductor to ground.

Note (optional)

Megger test voltage used critical (required)

Enter the test voltage applied during the insulation resistance test.

Note (optional)

Test duration / stabilization time

Record the time allowed for the reading to stabilize before recording the result.

Reading taken from loop to ground with other conductors isolated critical (required)

Confirm the measurement was taken with the correct conductor isolated and the other lead on ground.

Yes No N/A

Pre-installation or baseline reading available

Indicate whether a baseline reading was taken before installation or prior to repair.

Yes No N/A

Acceptance, Deficiencies, and Closeout

Deficiencies or non-conformances observed

Select any observed issues requiring correction.

Note (optional)

Corrective action required and assigned critical (required)

Indicate whether corrective action is needed to resolve any deficiency.

Yes No N/A

Final acceptance status critical (required)

Select the final disposition of the loop circuit after inspection.

Inspector signature critical (required)

Sign to certify the accuracy of the inspection record.

Get your results

Enter your email — we'll send you a PDF of your filled-out template, plus the occasional MangoScoop newsletter (templates, workflow tips, product updates). Unsubscribe anytime — link is in every email.

Email (required)

Your name (optional)

Run: Traffic Signal Loop Splice and Megger Test Inspection

Inspection Details

Safety and Test Preconditions

Loop Wiring and Splice Verification

Electrical Test Results

Acceptance, Deficiencies, and Closeout

Get your results