Run Insulation Continuity Inspection — Free

Inspection Details

Project / area inspected

Identify the building, floor, room, assembly, or envelope area inspected.

Inspection date and time critical (required)

Record when the inspection was performed.

Inspector name and role critical (required)

Enter the inspector's name and title or qualification.

Inspection basis

Select the reason for the inspection.

Reference standard or specification

List the applicable project specification, manufacturer guidance, or code reference used for the inspection.

Insulation Coverage and Continuity

Installed insulation type matches approved specification critical (required)

Verify the insulation material and assembly match the approved design or submittal.

Yes No N/A

Photo evidence (optional)

Installed thickness meets specified depth critical (required)

Measure installed thickness at representative locations.

Measured or documented R-value meets design requirement critical (required)

Record the installed or verified R-value for the inspected assembly.

Insulation coverage is continuous across the inspected area critical (required)

Confirm there are no missing sections, voids, or uninsulated areas within the inspected envelope segment.

Yes No N/A

Photo evidence (optional)

Gaps, voids, or slumps observed critical (required)

Identify whether gaps, voids, slumping, or displaced insulation are present.

Yes No N/A

Photo evidence (optional)

Compression or overfill affecting performance critical (required)

Check for compression, overpacking, or other conditions that reduce effective R-value.

Yes No N/A

Photo evidence (optional)

Coverage at corners, edges, and transitions

Rate continuity at corners, edges, and transitions where coverage is commonly interrupted.

Thermal Bridges and Air Sealing

Thermal bridges minimized at framing, fasteners, and structural members critical (required)

Verify that thermal bridging is addressed where framing, fasteners, or structural elements interrupt the thermal envelope.

Yes No N/A

Photo evidence (optional)

Air barrier is continuous across the inspected assembly critical (required)

Confirm the air barrier is continuous and aligned with the insulation layer where required by the assembly design.

Yes No N/A

Photo evidence (optional)

Penetrations are sealed critical (required)

Check sealing at pipes, conduits, ducts, wires, and other penetrations through the thermal envelope.

Yes No N/A

Photo evidence (optional)

Joints, seams, and transitions are sealed critical (required)

Verify sealant, tape, foam, gaskets, or other approved methods are installed at joints and transitions.

Yes No N/A

Photo evidence (optional)

Openings around windows, doors, and service chases are sealed critical (required)

Inspect perimeter sealing at openings and service chases for visible discontinuities or air leakage paths.

Yes No N/A

Photo evidence (optional)

Installation Quality and Compliance

Insulation is installed without damage or contamination critical (required)

Check for wet, torn, compressed, dirty, or otherwise compromised insulation.

Yes No N/A

Photo evidence (optional)

Vapor retarder or facing is installed as specified

Verify the vapor retarder or facing orientation and continuity where required by the assembly design.

Yes No N/A

Photo evidence (optional)

Observed deficiencies documented for corrective action critical (required)

List all deficiencies, non-conformances, and locations requiring rework or verification.

Inspector overall condition rating

Provide an overall rating of the inspected insulation continuity and air sealing condition.

Corrective Actions and Sign-Off

Corrective actions assigned

Select the required follow-up actions for any deficiencies found.

Note (optional)

Target completion date

Enter the date and time by which corrective actions should be completed.

Note (optional)

Inspector signature critical (required)

Inspector sign-off confirming the inspection findings.

Supervisor / AHJ review

Optional approval by supervisor, quality manager, or Authority Having Jurisdiction (AHJ).

Get your results

Enter your email — we'll send you a PDF of your filled-out template, plus the occasional MangoScoop newsletter (templates, workflow tips, product updates). Unsubscribe anytime — link is in every email.

Email (required)

Your name (optional)

Run: Insulation Continuity Inspection

Inspection Details

Insulation Coverage and Continuity

Thermal Bridges and Air Sealing

Installation Quality and Compliance

Corrective Actions and Sign-Off

Get your results