Run Crane / Rigging Daily Inspection — Free

Inspection Scope & Pre-Use Readiness

Inspection completed before crane or rigging is placed in service critical (required)

Confirm the daily inspection is performed before the first lift or shift use.

Yes No N/A

Inspector is a qualified operator or competent person critical (required)

Verify the person completing the inspection is authorized and competent for crane/rigging checks.

Yes No N/A

Crane identification and configuration recorded

Record crane ID, type, and current configuration or setup location.

Lift type identified

Select the primary lift category for this inspection.

Crane Structure, Controls & Safety Devices

No visible structural cracks, deformation, or missing fasteners critical (required)

Inspect boom, jib, mast, superstructure, carbody, and accessible structural members for damage or looseness.

Yes No N/A

Controls, limit devices, and indicators function properly critical (required)

Verify operating controls, limit switches, load indicators, and other safety devices respond as intended.

Yes No N/A

Brakes, hoist, and swing/travel functions operate normally critical (required)

Check for abnormal noise, drift, slippage, delayed response, or other operational deficiencies.

Yes No N/A

Cab, access points, and walkways are free of hazards

Verify access ladders, steps, handholds, and cab areas are secure, clean, and unobstructed.

Yes No N/A

Warning labels, load chart, and capacity markings are legible

Confirm required markings are present and readable from the operator position.

Yes No N/A

Wire Rope, Hooks & Load-Holding Components

Wire rope shows no broken wires, crushing, kinks, birdcaging, or excessive wear critical (required)

Inspect all accessible wire rope sections for visible damage or deterioration.

Yes No N/A

Wire rope reeving and end terminations are secure critical (required)

Check for proper reeving, secure terminations, and no evidence of slippage or distortion.

Yes No N/A

Hook is not bent, twisted, cracked, or excessively worn critical (required)

Inspect the hook body and throat opening for deformation or other visible deficiency.

Yes No N/A

Hook latch or safety device is present and functional critical (required)

Confirm the latch closes properly and prevents accidental disengagement of the load.

Yes No N/A

Sheaves, blocks, and load-bearing pins are intact and aligned

Check for cracked sheaves, damaged grooves, missing retainers, or abnormal wear.

Yes No N/A

Outriggers, Supports & Ground Conditions

Outriggers extend, lock, and hold position properly critical (required)

Verify outriggers or stabilizers deploy correctly and remain secure under setup conditions.

Yes No N/A

Outrigger pads / mats are present, correctly sized, and undamaged critical (required)

Confirm pads or mats are suitable for the load and free of cracks, splits, or excessive deformation.

Yes No N/A

Ground bearing surface is stable and level enough for the planned lift critical (required)

Assess soil, pavement, slabs, trenches, voids, and slope for stability and settlement risk.

Yes No N/A

No overhead or side obstructions in the planned travel or swing path critical (required)

Verify the work area is clear of power lines, structures, stored materials, and other obstructions.

Yes No N/A

Rigging, Slings & Lift Hardware

Slings show no cuts, broken strands, abrasion, heat damage, or chemical damage critical (required)

Inspect wire rope, chain, synthetic web, and round slings used in the lift.

Yes No N/A

Shackles, hooks, eyebolts, and other rigging hardware are undamaged and properly marked critical (required)

Confirm hardware is not bent, cracked, stretched, or missing required identification markings.

Yes No N/A

Rigging configuration matches the planned load and hitch method critical (required)

Verify sling angles, hitch type, and attachment points are appropriate for the load and lift plan.

Yes No N/A

Deficiencies, Corrective Actions & Sign-Off

Deficiencies documented

List all deficiencies, non-conformances, or critical items found during the inspection.

Equipment removed from service if any critical item failed critical (required)

Confirm the crane, rigging, or affected component was tagged out and taken out of service when required.

Yes No N/A

Inspector signature

Signature of the person completing the inspection.

Get your results

Enter your email — we'll send you a PDF of your filled-out template, plus the occasional MangoScoop newsletter (templates, workflow tips, product updates). Unsubscribe anytime — link is in every email.

Email (required)

Your name (optional)

Run: Crane / Rigging Daily Inspection

Inspection Scope & Pre-Use Readiness

Crane Structure, Controls & Safety Devices

Wire Rope, Hooks & Load-Holding Components

Outriggers, Supports & Ground Conditions

Rigging, Slings & Lift Hardware

Deficiencies, Corrective Actions & Sign-Off

Get your results