Run Battery Test Bay Conductance Tester Calibration Audit — Free

Tester Identification and Readiness

Tester present at assigned bay and matches asset ID critical (required)

Verify the tester is located in the designated battery test area and the asset tag/serial number matches the store's assigned equipment record.

Yes No N/A

Power on and completes startup/self-test without error critical (required)

Turn the unit on and confirm it boots normally, displays no fault codes, and completes any built-in self-check.

Yes No N/A

Display, keypad, cables, and clamps are intact critical (required)

Inspect for cracked housing, unreadable display, damaged buttons, frayed leads, loose connectors, or corroded clamps.

Yes No N/A

Photo evidence (optional)

Tester is clean, dry, and free of battery acid residue critical (required)

Check the unit and leads for contamination, moisture, or visible electrolyte residue that could affect safe operation or readings.

Yes No N/A

Work area around tester is unobstructed and safe to access

Confirm the bay area allows safe access to the tester, battery staging area, and customer interaction space without trip hazards or blocked movement.

Yes No N/A

Calibration and Verification Status

Current calibration or verification label is present and legible critical (required)

Confirm the unit has a visible calibration/verification label or sticker showing the current status and due date.

Yes No N/A

Photo evidence (optional)

Calibration or verification is within required interval critical (required)

Confirm the tester is within the store-required calibration or verification interval and not overdue.

Yes No N/A

Daily calibration audit or known-good verification completed critical (required)

Document that the tester was checked against the approved daily verification method or known-good reference battery per SOP.

Yes No N/A

Reference battery or verification standard available and in serviceable condition

If your process uses a reference battery or standard, confirm it is identified, available, and not damaged or out of service.

Yes No N/A

Last annual calibration or health check date recorded

Enter the date of the most recent annual calibration, health check, or manufacturer service event if required by the store program.

Test Accuracy and Functional Check

Test result display is readable and reports complete output critical (required)

Run a sample test or built-in check and verify the screen clearly displays battery condition, voltage, and any required pass/fail or code output.

Yes No N/A

Voltage reading is within acceptable range for a known-good check critical (required)

Record the measured voltage from the verification check. Use the site-approved known-good battery or reference method.

Tester prompts and menus operate normally

Confirm buttons, touchscreen, or menu navigation respond correctly and do not freeze, lag, or misread inputs.

Yes No N/A

Leads and clamps maintain secure contact during test critical (required)

Verify the clamps grip firmly and the tester does not lose contact or produce intermittent readings during the check.

Yes No N/A

Tester output matches expected result for verification battery critical (required)

Compare the displayed result to the expected range or status for the approved verification battery or standard.

Yes No N/A

Documentation and Records

Daily audit log completed

Confirm the daily calibration audit or verification log was filled out for this unit and date.

Yes No N/A

Calibration certificate or service record on file

Verify the current calibration certificate, service record, or maintenance history is available in the store file or system.

Yes No N/A

Any deficiency documented with corrective action owner and due date critical (required)

If a problem was found, document the deficiency, assigned owner, and expected completion date.

Yes No N/A

Out-of-service tag applied when tester is not fit for use critical (required)

If the tester fails verification, confirm it is removed from service and clearly tagged to prevent use.

Yes No N/A

Closeout and Sign-Off

Supervisor or manager notified of any critical failure critical (required)

Confirm escalation occurred for any critical item failure, overdue calibration, or out-of-service condition.

Yes No N/A

Inspector comments

Add any notes about unusual readings, maintenance needs, or follow-up actions.

Inspector signature critical (required)

Signature of the person completing the daily audit.

Get your results

Enter your email — we'll send you a PDF of your filled-out template, plus the occasional MangoScoop newsletter (templates, workflow tips, product updates). Unsubscribe anytime — link is in every email.

Email (required)

Your name (optional)

Run: Battery Test Bay Conductance Tester Calibration Audit

Tester Identification and Readiness

Calibration and Verification Status

Test Accuracy and Functional Check

Documentation and Records

Closeout and Sign-Off

Get your results